Cleburne Electrical Company handles electrical repair and installation for homes, rental properties, and businesses throughout Cleburne and the surrounding area. Whether you need a single outlet fixed or a full panel upgrade, we scope the job on the call and get it scheduled without the runaround. Residential wiring. Commercial wiring. One number for both.
From troubleshooting and diagnostics to code-compliant wiring for new construction and remodels, we cover the full range of electrical work that homeowners, landlords, and commercial property managers need. Call for a quote and we will tell you exactly what the job involves before anything is scheduled.
Getting your power back is easier than you think. When something goes wrong with your electrical system, the first step is understanding what actually caused it, not just swapping parts and hoping the problem goes away. We trace the fault before anything is replaced.
Dead outlets, flickering lights, a breaker that keeps tripping, a burning smell near an outlet, sparking or buzzing from a switch, a hot outlet cover, or half the house suddenly going dark, each of these symptoms points to something specific. Some are nuisances. Others are warning signs that call for prompt attention. We work through the symptom, identify the source, and explain what we found before any repair work begins.
That process includes checking GFCI and AFCI protection where it applies, testing arc-fault and ground-fault breakers, and confirming that a fix actually holds before we leave. We get to the bottom of the problem fast.
If you're not sure your panel can handle the load, that is a reasonable concern in a city where a lot of the housing stock was built before modern appliances, EV chargers, and home office setups became the norm. A panel that was sized for a different era of electrical demand may not be keeping up.
We handle 100-amp to 200-amp upgrades, main panel replacements, subpanel installation, and service-entrance and meter upgrades. Every job starts with a load calculation so the new panel is sized correctly for what the home or building actually draws. For older Cleburne properties being updated or converted, that calculation matters more than most people realize.
We treat your home and its wiring the way we would our own. That means the work is done carefully, the panel is labeled correctly, and the area around it is left clean when we go.
What sets this service apart is straightforward: we handle everything from a single outlet replacement to a full lighting redesign, and we do it without making a simple job complicated.
Outlet work includes standard replacements, GFCI outlet installation in kitchens, bathrooms, garages, and exterior locations, and AFCI outlet installation where the wiring configuration calls for it. Switch work covers everything from a basic swap to dimmer switch installation and multi-location wiring. On the lighting side, we install recessed lighting, LED fixtures, under-cabinet lighting, and ceiling fans, including the wiring and switch work that goes with each.
Adding a circuit is often simpler than people expect. If you need a new outlet run for a home office, a dedicated line for a kitchen appliance, or a ceiling fan where there was no wiring before, a call is all it takes to find out what is involved. We'll get the job wired and finished.
In Cleburne, outdoor spaces get real use across most of the year. Patios, driveways, walkways, and garage approaches all benefit from lighting that is both functional and properly wired for the Texas climate.
We install exterior lighting of all kinds: landscape lighting wiring, security light installation, motion sensor lights, and weatherproof outlet installation for outdoor entertaining areas, tool use, or holiday displays. Every outdoor circuit is grounded and bonded correctly, which matters more on exterior runs that are exposed to heat, humidity, and the occasional hard rain.
If you want a lit pathway, a floodlight on the corner of the garage, or a weatherproof outlet on the back porch, we can scope the work on the call and get it on the schedule.
Some appliances and equipment need their own circuit, and some spaces need wiring built from scratch. We handle both.
Dedicated circuit installation covers kitchen appliances, laundry rooms, garage workshops, hot tubs, and pool electrical wiring. For remodels and additions, we rough in new wiring, run circuits to where they are needed, and tie everything back to the panel cleanly. New construction wiring follows the same process: the scope is confirmed before work starts and the job is done to the code inspectors in Johnson County enforce.
Older wiring types come up often in this area. Homes with knob-and-tube wiring or aluminum wiring can be updated, either in targeted areas or as a whole-home rewire, depending on what the inspection turns up. Call us and we'll walk you through the fix.
Johnson County's climate brings real electrical demand across every season. Hot summers push cooling loads hard, winter ice storms can knock out power for days, and the severe thunderstorms that move through this part of Texas are a regular feature of spring and fall. These three services come up often in Cleburne for exactly those reasons.
Older neighborhoods in Cleburne have a lot of panels that were never sized for what homes draw today. Air conditioning, electric ranges, EV chargers, and home workshops all add load, and a panel that cannot carry it safely is a problem that shows up as tripped breakers, warm panel covers, or lights that dim when an appliance kicks on. An upgrade starts with a load assessment, moves to selecting the right breaker box for the service level, and includes updating the service entrance where needed. The result is a panel that matches what the home actually requires.
Texas grid reliability has been a real concern, and Cleburne is not insulated from outages during ice storms or severe weather events. A standby generator gives a home or business a source of power when the grid goes down. On the electrical side, the job involves installing a transfer switch, wiring the generator connection to the panel, and making sure the panel has the capacity to handle the load the generator will feed. We do not install or service the generator unit itself, but we handle everything on the wiring and transfer-switch side.
A whole-house surge protector is wired directly at the panel and catches voltage spikes before they reach the circuits inside the home. In an area that sees the kind of lightning activity Johnson County gets during storm season, that layer of protection matters for televisions, computers, smart appliances, and anything else that runs on a circuit. The installation is straightforward, and grounding and bonding are confirmed as part of the job. Electrical service scheduled without the runaround means we get this on the calendar and get it done.
The wiring around here has its own patterns, and older homes in Cleburne often have a mix of updates done over the decades that do not always add up to a clean, code-compliant system. An electrical safety inspection goes through the panel, the wiring, the outlets, and the grounding to give you a clear picture of what is there and what may need attention.
Pre-purchase inspections are common for buyers looking at older properties in the area. Landlords and property managers use them to confirm that a rental unit is in good shape before a new tenant moves in, or to address issues flagged by a code inspection. We check GFCI and AFCI protection, look at the panel for signs of overloading or outdated breakers, and document what we find in plain language.
A Level 2 home EV charger installation is a straightforward job when the panel has the capacity for it, and a more involved one when it does not. We start with a panel capacity check before any wiring is run, so you know what the job actually involves before anything is scheduled.
The installation includes running a dedicated circuit from the panel to the charger location, installing the outlet or hardwired connection the charger requires, and confirming that the circuit is sized correctly for the charger's draw. If the panel needs an upgrade or a subpanel to support the new circuit, we handle that as part of the same project. Have the charger unit and your preferred mounting location in mind before you call, and we will scope the rest on the phone.
We take work throughout Cleburne and the towns nearby. If you are in Johnson County or just across the county line, call and we will confirm whether your address is in our service area.
Communities we serve include Burleson, Joshua, Godley, Alvarado, Keene, Crowley, and Venus.
Electrical work is easier to price when the job is scoped first, and that is exactly what happens on the call. You describe what is going on, we ask the questions that help us understand the scope, and you get a rate before anything is put on the calendar.
If you are not sure what the job involves, that is fine. Part of what the call covers is helping you figure out what you actually need. Ask what the visit includes and you will get a straight answer. The price is confirmed before we schedule, so there is nothing to guess at.
We are available every day from 8:30 AM to 9:30 PM.
A whole-home surge protector installs at the service entrance and catches large voltage spikes before they reach the circuits inside the house. In Johnson County, where severe thunderstorms and lightning activity are a regular part of storm season, that layer of protection matters for major appliances, electronics, and HVAC equipment that a plug-in strip cannot fully cover. We install the protector at the panel, confirm the grounding and bonding is solid, and the installation is straightforward.
A Level 2 home EV charger requires a dedicated 240-volt circuit, and the first step is confirming the panel has the capacity to support it. If the panel is already at or near capacity, an upgrade or subpanel may be part of the same project. We start with a panel capacity check, run the circuit to your preferred charger location, and install the outlet or hardwired connection the charger requires.
A transfer switch isolates your home's wiring from the utility feed before the generator is connected, which prevents backfeed from reaching the utility lines and protects anyone working on them during an outage. Without a transfer switch, connecting a generator directly to the panel is a safety and legal problem. We install the transfer switch, wire the generator connection to the panel, and confirm the panel has the capacity to carry the generator's load.
Flickering lights are often caused by a loose connection at the fixture, the switch, or further back in the circuit, and in some cases they point to a larger load issue at the panel. Dimming that happens when a major appliance kicks on usually means the circuit is undersized or the panel is running near capacity. We trace the fault before replacing anything, so the fix addresses the actual cause rather than the symptom.
Homes built before modern electrical loads were common were wired for a fraction of what a typical household now draws. Fewer circuits, lower service amperage, and panels that have never been updated all contribute to the problem. Adding dedicated circuits and upgrading the panel to match current demand is usually the right answer, and it starts with a load calculation to confirm what the service actually needs to carry.
If a breaker has tripped, leave it off rather than resetting it repeatedly. If you smell burning or see sparking, turn off the circuit at the panel if you can do so safely, and move away from the affected outlet or switch. Do not use the outlet or switch until it has been inspected.
Call (682) 496-2395 and describe what is happening so we can help you assess the situation before we arrive.
Replacing a like-for-like outlet or switch is something many homeowners handle without issue, provided the circuit is turned off at the breaker first and the connections are made correctly. Anything involving the panel, new wiring runs, GFCI or AFCI installation in locations where it was not previously present, or a fault that has not been identified is work that needs to be traced and handled properly. If you are not certain what is causing the problem, a call is the right first step.
Rain and wet conditions affect outdoor electrical work, particularly for exposed wiring runs and fixture installation. We confirm conditions on the day of the job and let you know if the schedule needs to shift. Weatherproof outlets, outdoor fixtures, and landscape lighting circuits are all designed for the Texas climate, and the installation is done to account for heat, humidity, and exposure.
When a ceiling fan goes where there was no wiring before, the job involves running a circuit from the panel or a nearby junction point, installing a properly rated ceiling box, and wiring the fan and its controls. If you want a separate switch for the fan and the light, that adds a two-conductor run from the switch location. We scope the wiring work on the call so you know what is involved before we schedule.
The answer depends on what the panel is currently rated for, how much of that capacity is already in use, and what the charger you are installing requires. A 200-amp panel with available breaker slots and room in the load calculation can often support a Level 2 charger without changes. A panel that is already loaded close to its limit may need an upgrade or a subpanel first. We confirm the panel's capacity before any wiring is run.
A quick repair addresses a specific fault: a failed outlet, a bad connection, a tripped breaker with a clear cause. A rewire becomes the right answer when the wiring itself is the problem throughout a section of the home or the whole house, as is common with knob-and-tube or aluminum branch circuit wiring. The inspection tells you which situation you are in, and we explain what we found before any work is proposed.
Real experience. Local knowledge. Ready to wire.
When you call, you reach someone who can scope the job, answer your questions, and get the work scheduled. The work area is left as it was found, and the job is explained before it starts.
Call (682) 496-2395 between 8:30 AM and 9:30 PM any day of the week to get a quote.
Below is a plain-language look at the electrical work we handle for homes, rental properties, and businesses in Cleburne and Johnson County. Each row covers what the service involves, who it fits best, and one practical thing worth knowing before you call. If your situation does not fit neatly into a row, call us and we will scope it on the phone.
| Type of Work | What the Job Involves | Ideal For | Worth Knowing |
|---|---|---|---|
| Electrical Repairs & Troubleshooting | Dead outlets and failed switches, Flickering or dimming lights, Burning smells and buzzing fixtures, Fault tracing before any part is replaced | Any home or business with an unexplained electrical symptom | The fault is traced and confirmed before anything is replaced, so the repair addresses the actual cause rather than the visible symptom. |
| Breaker & Fuse Repair | Breaker that trips and will not reset, Fuse panel evaluation, AFCI and GFCI breaker testing, Breaker replacement | Homes where a circuit keeps going out or a breaker runs warm | A breaker that trips repeatedly is telling you something about the load or the wiring on that circuit, not just the breaker itself. We check both before swapping hardware. |
| Outlet & Switch Installation | Standard and GFCI outlet replacement, AFCI outlet installation, Dimmer and multi-location switch wiring, New outlet runs for home offices or appliances | Homeowners adding outlets or replacing outdated switches and receptacles | GFCI protection is required by code in kitchens, bathrooms, garages, and exterior locations. If yours are missing, we can add them as a standalone job. |
| Wiring & Circuit Installation | New circuit runs to any room, Rough-in wiring for remodels and additions, New construction wiring, Panel tie-in and labeling | Additions, remodels, and new builds that need circuits run from scratch | Wiring for additions and remodels is done to the code inspectors in Johnson County enforce. The scope is confirmed before work starts. |
| Backup Generator Installation | Transfer switch installation, Generator-to-panel wiring, Panel capacity assessment, Load confirmation for generator feed | Homes and businesses preparing for grid outages during ice storms or severe weather | We handle the transfer switch and all wiring on the electrical side. The generator unit itself is outside our scope, so have your unit selected before you call. |
| EV Charger Installation | Panel capacity check before wiring, Dedicated 240-volt circuit, Outlet or hardwired charger connection, Subpanel addition if needed | Homeowners installing a Level 2 home EV charger | The first step is always a panel capacity check. If the panel cannot support the new circuit, we handle the upgrade as part of the same project. |
| Dedicated Appliance Circuits | Kitchen appliance circuits, Laundry and dryer circuits, Garage workshop circuits, Hot tub and pool electrical wiring | Homeowners adding a major appliance or workshop equipment that needs its own circuit | Most large appliances require a dedicated circuit that is not shared with anything else. Adding one is often simpler than people expect, and we confirm the panel has room before running wire. |
| Whole-Home Surge Protection | Panel-level surge protector installation, Grounding and bonding confirmation, Protection for appliances and electronics, Single-visit installation | Any home in an area with frequent lightning or storm activity | A panel-level surge protector catches voltage spikes before they reach the circuits inside the home. Plug-in strips alone do not provide the same level of protection. |
| Ceiling Fan Installation | Fan and light kit wiring, Ceiling box upgrade for fan-rated support, Separate switch runs for fan and light, New wiring where none exists | Rooms being updated or locations with no existing wiring overhead | Installing a fan where there was no wiring before means running a circuit and installing a fan-rated ceiling box. We scope both on the call so nothing surprises you. |
| Lighting Installation | Recessed and LED fixture installation, Under-cabinet lighting, Outdoor and security lighting, Landscape lighting wiring | Remodels, new construction, and exterior lighting projects | Outdoor fixtures on exterior runs in the Texas climate need to be properly grounded and weatherproofed. We confirm both as part of every outdoor lighting install. |
| Electrical Panel & Service Upgrades | 100-amp to 200-amp service upgrades, Main panel replacement, Subpanel installation, Load calculation before sizing | Older Cleburne homes being updated, or any property adding significant new load | Every upgrade starts with a load calculation so the new panel is sized for what the home actually draws, not just what it drew when it was built. |
| Older-Home Rewiring | Knob-and-tube wiring replacement, Aluminum branch circuit updates, Targeted section rewires, Whole-home rewire where needed | Older Cleburne properties with wiring that has not been updated | An inspection tells you whether a targeted repair or a full rewire is the right answer. We explain what we find before any work is proposed. |
What are the signs that a panel upgrade is overdue?
The most common signs are breakers that trip under normal household loads, lights that dim when a large appliance kicks on, a panel cover that feels warm to the touch, and a panel that has no room for additional breakers. Older panels rated at 60 or 100 amps were sized for a different era of electrical demand. A load calculation tells you whether the current service level can carry what the home actually draws under real conditions.
What causes a breaker to trip repeatedly, and when is it a wiring problem rather than just the breaker?
A breaker trips when the circuit draws more current than it is rated for. That can mean the circuit is overloaded with too many devices, the breaker itself is worn and tripping at a lower threshold than it should, or there is a fault somewhere in the wiring. Repeated tripping on the same circuit after you have reduced the load on it usually points to a wiring or connection issue rather than the breaker. We check the circuit before replacing hardware.
Is electrical work in Cleburne permitted and inspected?
Most electrical work beyond straightforward like-for-like replacements requires a permit and an inspection through the local authority. That applies to panel upgrades, new circuit runs, service entrance work, and wiring for additions or remodels. We confirm what is required for your specific job before work begins, and the work is done to the code inspectors in Johnson County enforce.
Faults Traced Before Anything Is Replaced
We identify the source of the problem before recommending a repair. That means the fix addresses what actually caused the fault, not just the part that stopped working.
How do I know if my home is ready for added electrical load, like a new appliance or an EV charger?
The answer starts with knowing what the panel is currently rated for and how much of that capacity is already committed to existing circuits. A panel that is near its limit may need an upgrade before a new circuit can be added safely. We do a load assessment before running any new wiring, so you know what the job involves before anything is scheduled.
What are the risks of aluminum or knob-and-tube wiring in an older home?
Knob-and-tube wiring was not designed for modern electrical loads and lacks a ground conductor, which limits where it can be used safely in a home wired to current standards. Aluminum branch circuit wiring from the 1960s and 1970s can develop connection problems over time that create heat at outlets and switches. Both can be updated, either in targeted areas or as a whole-home rewire. An inspection tells you what is present and what condition it is in.
Why do outlets and switches stop working even when the breaker has not tripped?
A dead outlet with no tripped breaker usually points to a loose or failed connection at the outlet itself, a tripped GFCI outlet upstream on the same circuit, or a wiring fault between the outlet and the panel. GFCI outlets protect other outlets downstream from them, so a tripped GFCI in one room can knock out outlets in another. We check the full circuit rather than just the outlet that stopped working.
Scope Agreed Before the Panel Is Opened
The job is scoped on the call and confirmed before work begins. You know what is involved and what it covers before anyone shows up at the property.
What does adding a circuit for a workshop or garage require?
A garage workshop circuit starts with a panel capacity check to confirm there is room for the new breaker. From there, we run the circuit to the workshop location, install the outlets in the right configuration for the equipment you are running, and tie it back to the panel. If you are running high-draw tools like a table saw or air compressor, a dedicated 240-volt circuit may be the right answer rather than a standard 120-volt run.
How does GFCI protection work, and where is it required?
A GFCI outlet or breaker monitors the current flowing through a circuit and trips within milliseconds if it detects an imbalance, which is what happens when current finds a path to ground through a person. Code requires GFCI protection in kitchens, bathrooms, garages, unfinished basements, outdoor locations, and anywhere near a water source. Older homes often have none of this protection in place, and adding it is a straightforward job.
Older and Newer Wiring Both Handled
From knob-and-tube and aluminum branch circuits to modern panel upgrades and EV charger installs, we work across the full range of wiring types common in Johnson County homes.
How long does a panel upgrade typically take?
A straightforward panel replacement on a home with a standard service entrance usually takes the better part of a day. The power to the home is off for the duration of the swap. If the service entrance needs updating at the same time, or if the job involves adding a subpanel, the timeline extends. We confirm the scope on the call so you know what to expect before the work is scheduled.
What should I know about grounding and bonding in an older Cleburne home?
Homes built before the mid-1960s were often wired without a ground conductor in the branch circuits. That means two-prong outlets throughout the home and no ground path for appliances that require one. Grounding and bonding can be addressed in several ways depending on the wiring configuration, and we explain the options after the inspection rather than assuming one approach fits every situation.
How does backup generator sizing work on the electrical side?
The electrical side of generator sizing is about confirming the panel has the capacity to carry the load the generator will feed during an outage. That means identifying which circuits matter most, making sure the panel can handle the generator's output, and installing a transfer switch sized for the application. The generator unit itself determines the total output available, so having a unit selected before you call helps us scope the panel and transfer switch work accurately.
Call (682) 496-2395 between 8:30 AM and 9:30 PM any day of the week and we will scope the job, answer your questions, and get the work on the calendar.
(682) 496-2395